View GBM-9100F_1244280.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Optoway
GBM-9000F 5V / 850 nm / 2.125 Gb/s Multi-Mode Gigabit Interface Converter (GBIC)
FEATURES DESCRIPTION
GBM-9000F
*******************************************************************************************************************************************************************************
******************************************************************************************************************************************************************************
l Up to 2.5 Gbps Bi-directional Data Links l Compliant with 1X / 2X Fibre Channel FC-PI 13.0 l Compliant with Gigabit Interface Converter (GBIC) Specification Rev. 5.5 l 850 nm VCSEL Laser Transmitter l Hot Pluggable module with Duplex SC Connector l Multi-rate Operation for 2.5 / 2.125 / 1.062 / 1.25 Gbps l Link Distance at 2.125 Gbd 150 m links with 62.5/125 m MMF Cables 300 m links with 50/125 m MMF Cables l Link Distance at 1.026 Gbd 300 m links with 62.5/125 m MMF Cables 550 m links with 50/125 m MMF Cables l SCA-2 Host Connector l Single +5 V Power Supply l Differential PECL Inputs and Outputs l TTL RX-LOS Output l Class 1 Laser International Safety Standard IEC-60825 Compliant
The GBM-9000F series optical transceivers meet the Gigabit Interface Converter (GBIC) specification Rev. 5.5. It satisfies the optical interface specifications defined in IEEE 802.3z Drift 5.0 1000 BASE-SX for Gigabit Ethernet and 1x / 2x Fibre Channel FC-PI 13.0. This module is designed for multi-mode fiber and operates at a nominal wavelength of 850 nm. The transmitter section uses a multiple quantum well VCSEL and is a class 1 laser compliant according to International Safety Standard IEC60825. The receiver section uses an integrated GaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL input / output logic interface is used. TTL RX-LOS output simplifies interface to external circuitry. A 20-pin SCA-2 host connector is used to connect the converter to the host system.
LASER SAFETY
This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug.
APPLICATIONS
l Switch to Switch Interface l High Speed Interface for File Servers l Data Storage l Dual Rate 1.06 / 2.125 Gb/s Fibre Channel
ORDER INFORMATION
P/No. GBM-9000F GBM-9100F Bit Rate (Gb/s) 2.125/1.063 2.125/1.063 1000 BASE Distance Wavelength (m) (nm) Voltage (V) Connector Temp. (oC) TX Power RX Sens. (dBm) (dBm) -4 to -9.5 -4 to -9.5 -17 -17 150/300* 850 5 SC 0 to 70 SX 150/300* 850 3.3 SC 0 to 70 SX * At 2.125Gb/s: 150 m using 62.5 m MMF optic cable; 300 m using 50 m MMF optic cable
Absolute Maximum Ratings
Parameter Storage Temperature Operating Temperature Power Supply Voltage Input Voltage Symbol Tstg Topr Vcc --Min -40 -5 -0.5 -0.5 Max 85 70 6 Vcc Units o C o C V V Notes Air flow 1m/sec
Recommended Operating Conditions
Parameter Power Supply Voltage Power Supply Current Operating Temperature Data Rate Fiber Length on 50/125 m 500MHz-km Fiber Fiber Length on 62.5/125 m 200MHz-km Fiber Symbol Vcc ITX + IRX Topr Min 4.75 0 1.0625 / 1.25 2.125 / 2.5 550 300 300 150 Typ 5 200 Max 5.25 300 70 Units V mA C Gb/s m m
o
Conditions Reference to GND. Air flow 1m/sec
@1.0625 Gb/s @2.125Gb/s @1.0625 Gb/s @2.125Gb/s
******************************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw
12/1/2003 V1.0
Optoway
Transmitter Specifications (0 oC < Topr < 70 oC, 4.75 V < Vcc < 5.25V)
Parameter Symbol Optical Optical Transmit Power Po Output Center Wavelength Output Spectrum Width Extinction Ratio ER Optical Modulation Amplitude OMA (Peatk-to-Peak) Optical Rise Time tr Optical Fall Time tf Relative Intensity Noise RIN Pout TX_Disable Asserted P OFF Electrical Differential Input Voltage V IH - VIL TX-FAULTLOAD Transmit Fault Load VTX-FAULT-L Transmit Fault Output-Low Transmit Fault Output-High VTX-FAULT-H VTX-DISABLE-L TX-Disable Input - Low TX-Disable Input - High VTX-DISABLE-H TX-Disable Assert Time t_off TX-Disable Negate Time t-on Time to initialize, includes reset of t-int TX-FAULT TX FAULT from fault to assertion t-fault TX-Disable time to start reset t-reset Min -9.5 830 Typ --850 --9 Max -4 860 0.85 --Units dBm nm nm dB W ps ps dB/Hz dBm Vp-p k V V V V s ms ms s s
GBM-9000F
******************************************************************************************************************************************************************************
Notes 1 RMS () FC-PI Standard 20% to 80% value 20% to 80% value
196 150 150 -117 -35 0.65 4.7 0.0 Vcc - 0.5 0 2.0 2.0 10 0.5 Vcc + 0.3 0.8 Vcc + 0.3 10 1 300 100 10
2
1. Output power is power coupled into a 62.5/125 m or 50/125 m MM fiber. 2. Pull-up resistor on host Vcc.
Receiver Specifications (0oC < Topr < 70oC, 4.75 V < Vcc < 5.25V)
Parameter Optical
Sensitivity @ 1.25Gb/s @ BER=10-12 Sensitivity @ 2.125Gb/s @ BER=10-12
Symbol Sens (1X) Sens (2X) Pin
Min ---3 1.0 820 ---31 0.37
Typ ---
Max -18 -17 --860 -17 --2.0 0.35 0.35 10 0.8 Vcc 100 100
Units dBm dBm dBm dB nm dBm dBm Vp-p ns ns k V V s s
Notes 3 3 3
Maximum Input Power Signal detect - Hysteresis Wavelength of Operation RX-LOS - Asserted RX-LOS - Deasserted Electrical Differential Output Voltage Data Output Rise Time Data Output Fall Time Receiver Loss of Light Load
Loss of Signal Output Voltage --- Low Loss of Signal Output Voltage --- High Loss of Signal Assert Time (off to on) Loss of Signal Deassert Time (on to off)
Pa Pd RX-DAT TrRX-DAT TfRX-DAT RX-LOSLOAD RX-LOSL RX-LOSH TA,RX-LOS TD,RX-LOS
---------
Transition: low to high Transition: high to low
4.7 0 2.4
4
3. Minimum sensitivity and saturation levels at BER=1E-12 for a 27-1 PRBS. 4. Pull-up resistor on host Vcc.
******************************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798 E-mail: sales@optoway.com.tw Fax: 886-3-5979737 http: // www.optoway.com.tw
12/1/2003 V1.0
Optoway
PIN ASSIGNMENT
GBM-9000F
******************************************************************************************************************************************************************************
PIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Signal Name
RX-LOS RGND RGND MOD-DEF(0) MOD-DEF(1) MOD-DEF(2) TX-DIABLE TGND TGND TX-FAULT RGND -RX-DAT +RX-DAT RGND VCCR VCCT TGND +TX-DAT -TX-DAT TGND
Sequence
2 2 2 2 2 2 2 2 2 2 1 1 1 1 2 2 1 1 1 1
Description
Receiver Loss of Signal, logic high, open collector compatible, 4.7K to 10K ohm pull-up to VCCT on host Receiver Ground Receiver Ground TTL Low SCL Serial Clock Signal SDA Serial Data Signal Transmitter Disable, logic high, open collector compatible Transmitter Ground Transmitter Ground Transmitter Fault, logic high, open collector compatible, 4.7K to 10K ohm pull-up to V CCT on GBIC Receiver Ground Receiver Data Bar, Differential PECL, AC coupled Receiver Data, Differential PECL, AC coupled Receiver Ground Receiver +5V Supply Transmitter +5V Supply Transmitter Ground Transmitter Data, Differential PECL, AC coupled Transmitter Data Bar, Differential PECL, AC coupled Transmitter Ground
A sequence value of 1 indicates that the signal is in the first group to engage during plugging of a module. A sequence value of 2 indicates that the signal is the second and last group. The two guide pins on the connector are electrically connected to the transceiver circuit ground. These two guide pins make contact with circuit prior to sequence 1 signals.
Module Definition Module Definition
4
MOD-DEF(0) PIN 4
TTL Low
MOD-DEF (1) PIN 5
SCL
MOD-DEF (2) PIN 6
SDA
Interpretation by Host
Serial module definition protocol
Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E2PROM protocol of the ATMEL AT24C01A/02/04 family of components.
******************************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798 E-mail: sales@optoway.com.tw Fax: 886-3-5979737 http: // www.optoway.com.tw
12/1/2003 V1.0
Optoway
PACKAGE DIAGRAM
Units in mm
GBM-9000F
******************************************************************************************************************************************************************************
Note: Specifications subject to change without notice.
******************************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798 E-mail: sales@optoway.com.tw Fax: 886-3-5979737 http: // www.optoway.com.tw
12/1/2003 V1.0

▲Up To Search▲

Price & Availability of GBM-9100F

	To Download GBM-9100F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .